How to Shock a Saltwater Pool

How to Shock a Saltwater Pool

Can you add shock to a saltwater pool?

How to Shock a Saltwater Pool, there are two types of shocks: liquid or crystal. You just need to drag it to the mixer to mix it up and it’s done. As recommended, mix shocks into the pool weekly. First of all, we need to find a very good quality shock that helps to get rid of algae around the pool. It helps in getting rid of the clouds in pool water. Saltwater pools are similar to chlorinated pools in that they aid in the removal of algae and keep the pool clean, clear, and healthy.

It helps to remove contamination

Something happens accidentally when some people peep or poo in the pool. It usually happens after a shock. It’s important to remove the debris.

There are some non-chlorine bleach shocks available on Amazon as well, just to maintain the cleaning of your pools. The non-chlorine pools are made with calcium, which usually doesn’t raise acidic levels. So it’s less harmful to those who swim around the pool. 

Always use a testing kit to maintain the pH level. Too acidic is not going to be safe. Too much chlorine can cause staining. The pool surface pH level should be around 7.4–7.6. The shocks are accounted for by the gallons of water that a pool contains. When a shock is added, the filtration system should be turned on in order to dispense it evenly around the pool. In addition, you should use algae cleaner, vacuum, and brush each side of the pool. Running the filter for 8 hours straight, bedside there is a pool clarifier. 

Make sure you test positive for pool chemistry so the chemicals react naturally. Pool alkalinity should be around 80-140 pH balanced. Ensure the poll shock is added in the amount specified per gallon and not more. Make an attempt to clear out all the germs, dirt, and even algae before adding the shock. Using the salt water chlorinator boosts the power of the chlorinator, removing all its dirt and its welcome guests. The reason we use a salt water chlorinator is to get rid of harmful bacteria or any type of living organism that is harmful to humans. Before adding the shock, I said some pool water to keep it warm. It’s not always the same spot. Pool maintenance should be done at least once a week.

The shock of the pool helps to remove the chloramines in the water with excessive odors, which can affect the eyes, causing them to become irritated. Shocking is basically adding some chlorine with some sanitizers to eliminate organic materials such as algae or substances. We use shock as not always saltwater works that effectively does remove the stains. Using filters is a must to help with disinfectants and dissolve in water. As a measure before, make sure the chlorine levels are not much higher than usual in case we need to turn off the chlorinator just to maintain the level of shock and the pool clarifier. It’s necessary to clean it before the shock. Remove rocks, sticks, any hard materials, or pool equipment. It’s not always effective during sunrise. It’s recommended to use the shock after or just before the sunset as the ultraviolet rays don’t make the procedure work. Never swim in shocked saltwater. Make sure the water level isn’t highly chlorinated. Just test the water beforehand, making sure it is around 1.1-3.0ppm

When a saltwater pool is shocked, it reverts back to salt. A saltwater pool has the same frequency as most chlorinated pools. Sometimes pools are contaminated due to vomit or blood. It causes it to spread diseases and leaves out some worms, dirt, and other harmful chemicals. Shock and chlorinator help to ease all types of germs or any disease. The shock causes some discoloration of any kind of metal sheet or iron, even copper left there. In the solution when the pH level is high, the chlorine reacts often slowly. People find crystalline deposits due to a higher level of calcium found in the pool.

The procedures to follow to shock your pool with a tablet or powder

Firstly, put the tablet into the skimmer. It gradually helps to dissolve the chlorine directly pumped into the pool. After a while, it’s dispersed. Secondly, you can just put the shock into a bucket full of water. It also gets the shock mixed up and then poured into the pool. The chlorinator just helps in getting it more sanitized. That’s not all. You have to open the spring when you know after chlorine measurement there shouldn’t be any chlorine level when it’s starting to shock the pool’s automatically generated chlorine with the salt water chlorinator. Sometimes a heavy rain might message with the level of the chemical added, so make sure you cover it up after it’s shocking. It doesn’t prevent algae from regrowing back, so make sure you keep doing the same process again and again.

 If your pool is susceptible to excessive algae growth, use an algaecide to remove its outbreak instead of using a high level of chlorine as it has to maintain its chemistry level. Shocking is needed when you close the pool, during heavy rain, or sometimes when it’s too sunny, so the best time for shocking a pool is in the evening time when the sunny ultraviolet rays damage the chlorine and terminate it instantly. Having too much chlorine can damage a saltwater base cell. It depends on the pool’s equipment and size. A 10,000-gallon pool may require 2 ounces of chlorine.

These are measured chemistry levels that should be maintained

2,700 to 3,400 ppm salt

1.0 to 3.0 ppm free chlorine

H: 7.2 to 7.8

Stabilizer: 60 ppm–80 ppm (ideal)

Total Alkalinity (TA) ranges from 80 to 120 ppm.

Calcium hardness ranges from 200 to 400 ppm.

Total Dissolved Solids: Less than 6,000 ppm




Please enter your comment!
Please enter your name here